TuYa TS0601_thermostat

   
Model TS0601_thermostat
Vendor TuYa
Description Radiator valve with thermostat
Exposes lock (state), switch (state), window_open, battery_low, position, climate (current_heating_setpoint, local_temperature, system_mode, local_temperature_calibration, preset, running_state), away_preset_days, boost_time, comfort_temperature, eco_temperature, force, max_temperature, min_temperature, away_preset_temperature, programming_mode, linkquality
Picture TuYa TS0601_thermostat
White-label Moes HY368, Moes HY369RT, SHOJZJ 378RT, Silvercrest TVR01, Immax 07732B, Evolveo Heat M30

Notes

Pairing

While pairing, keep the valve close to the coordinator.

  1. Turn the display on: Short press home (🏠).
  2. Enter settings: Long press home (🏠) for 3sec.
  3. Select WiFi settings: Press the plus button (➕) button 4 times to see the digital 5 on the right hand side and the blinking WiFi logo.
  4. Enter WiFi settings: Press home (🏠) once again. Now only WiFi logo is showing without blinking.
  5. Enable pairing mode: Long press home (🏠). WiFi logo is now blinking.
  6. Keep display on: Touch home (🏠) every few seconds.

Local temperature

If you’d like to force device to send local_temperature you can use this MQTT command:

  • topic: zigbee2mqtt/FRIENDLY_NAME/set/local_temperature_calibration
  • payload: YOUR_CURRENT_CALIBRATION_VALUE

YOUR_CURRENT_CALIBRATION_VALUE can be 0, but if you calibrated temperature for this device send current value. After this command thermostat responds with two messages. One for calibration change confirmation, and other with current local_temperature.

Controlling device specific features

  • If all you need is to control on and off, you can set “force” with topic zigbee2mqtt/FRIENDLY_NAME/set.

    The payload values are:
    open -> fully opens valve and stays there
    close -> fully closes valve and stays there
    normal -> normal valve operation

      {
      "force": "open"
  }

  • Use topic zigbee2mqtt/FRIENDLY_NAME/set/schedule to set the schedule of the device with 6 timeslots on workdays or holidays (e.g. weekend). Example payload values are:

      {
      "workdays":[
          {"hour":6,"minute":0,"temperature":19},
          {"hour":8,"minute":0,"temperature":20},
          {"hour":18,"minute":0,"temperature":21},
          {"hour":20,"minute":30,"temperature":20},
          {"hour":22,"minute":0,"temperature":19},
          {"hour":23,"minute":30,"temperature":15}
      ]
  }

      {
      "holidays":[
          {"hour":6,"minute":0,"temperature":19},
          {"hour":8,"minute":0,"temperature":20},
          {"hour":18,"minute":0,"temperature":21},
          {"hour":20,"minute":30,"temperature":20},
          {"hour":22,"minute":0,"temperature":19},
          {"hour":23,"minute":30,"temperature":15}
      ]
  }

  • You can set “week” schedule pattern with topic zigbee2mqtt/FRIENDLY_NAME/set. The payload values are: 5+2 -> to be used when workdays for example are monday-friday and saturday & sunday are holidays 6+1 -> to be used when workdays for example are monday-saturday and sunday is a holiday 7 -> to be used when workdays schedule will be used for the whole week

      {
      "week": "5+2"
  }

  • You can set “boost time” with topic zigbee2mqtt/FRIENDLY_NAME/set. But be aware that it rounds the values down to multiple of 100.

      {
      "boost_time": 200
  }

  • You can set “comfort temperature” level on the device with topic zigbee2mqtt/FRIENDLY_NAME/set.

      {
      "comfort_temperature": 21
  }

  • You can set “eco temperature” level on the device with topic zigbee2mqtt/FRIENDLY_NAME/set.

      {
      "eco_temperature": 17
  }

OTA updates

This device supports OTA updates, for more information see OTA updates.

Exposes

Lock

The current state of this lock is in the published state under the child_lock property (value is LOCK or UNLOCK). To control this lock publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"child_lock": "LOCK"} or {"child_lock": "UNLOCK"}. It’s not possible to read (/get) this value.

Switch

The current state of this switch is in the published state under the window_detection property (value is ON or OFF). To control this switch publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"window_detection": "ON"}, {"window_detection": "OFF"} or {"window_detection": "TOGGLE"}. It’s not possible to read (/get) this value.

Window_open (binary)

Window open?. Value can be found in the published state on the window_open property. It’s not possible to read (/get) or write (/set) this value. If value equals true window_open is ON, if false OFF.

Battery_low (binary)

Indicates if the battery of this device is almost empty. Value can be found in the published state on the battery_low property. It’s not possible to read (/get) or write (/set) this value. If value equals true battery_low is ON, if false OFF.

Switch

The current state of this switch is in the published state under the valve_detection property (value is ON or OFF). To control this switch publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"valve_detection": "ON"}, {"valve_detection": "OFF"} or {"valve_detection": "TOGGLE"}. It’s not possible to read (/get) this value.

Position (numeric)

Position. Value can be found in the published state on the position property. It’s not possible to read (/get) or write (/set) this value. The unit of this value is %.

Climate

This climate device supports the following features: current_heating_setpoint, local_temperature, system_mode, local_temperature_calibration, preset, running_state.

  • current_heating_setpoint: Temperature setpoint. To control publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"current_heating_setpoint": VALUE} where VALUE is the °C between 5 and 35. Reading (/get) this attribute is not possible.
  • local_temperature: Current temperature measured on the device (in °C). Reading (/get) this attribute is not possible.
  • system_mode: Mode of this device, in the heat mode the TS0601 will remain continuously heating, i.e. it does not regulate to the desired temperature. If you want TRV to properly regulate the temperature you need to use mode auto instead setting the desired temperature.. To control publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"system_mode": VALUE} where VALUE is one of: heat, auto, off. Reading (/get) this attribute is not possible.
  • preset: Mode of this device (similar to system_mode). To control publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"preset": VALUE} where VALUE is one of: schedule, manual, boost, complex, comfort, eco, away. Reading (/get) this attribute is not possible.
  • running_state: The current running state. Possible values are: idle, heat. Reading (/get) this attribute is not possible.
  • local_temperature_calibration: Offset to be used in the local_temperature. To control publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"local_temperature_calibration": VALUE}.The minimal value is -9 and the maximum value is 9 with a step size of 0.5.

Switch

The current state of this switch is in the published state under the auto_lock property (value is AUTO or MANUAL). To control this switch publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"auto_lock": "AUTO"}, {"auto_lock": "MANUAL"} or {"auto_lock": "undefined"}. It’s not possible to read (/get) this value.

Switch

The current state of this switch is in the published state under the away_mode property (value is ON or OFF). To control this switch publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"away_mode": "ON"}, {"away_mode": "OFF"} or {"away_mode": "undefined"}. It’s not possible to read (/get) this value.

Away_preset_days (numeric)

Away preset days. Value can be found in the published state on the away_preset_days property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"away_preset_days": NEW_VALUE}. The minimal value is 0 and the maximum value is 100.

Boost_time (numeric)

Boost time. Value can be found in the published state on the boost_time property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"boost_time": NEW_VALUE}. The minimal value is 0 and the maximum value is 900. The unit of this value is s.

Comfort_temperature (numeric)

Comfort temperature. Value can be found in the published state on the comfort_temperature property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"comfort_temperature": NEW_VALUE}. The minimal value is 0 and the maximum value is 30. The unit of this value is °C.

Eco_temperature (numeric)

Eco temperature. Value can be found in the published state on the eco_temperature property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"eco_temperature": NEW_VALUE}. The minimal value is 0 and the maximum value is 35. The unit of this value is °C.

Force (enum)

Force the valve position. Value can be found in the published state on the force property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"force": NEW_VALUE}. The possible values are: normal, open, close.

Max_temperature (numeric)

Maximum temperature. Value can be found in the published state on the max_temperature property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"max_temperature": NEW_VALUE}. The minimal value is 16 and the maximum value is 70. The unit of this value is °C.

Min_temperature (numeric)

Minimum temperature. Value can be found in the published state on the min_temperature property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"min_temperature": NEW_VALUE}. The minimal value is 1 and the maximum value is 15. The unit of this value is °C.

Away_preset_temperature (numeric)

Away preset temperature. Value can be found in the published state on the away_preset_temperature property. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"away_preset_temperature": NEW_VALUE}. The minimal value is -10 and the maximum value is 35. The unit of this value is °C.

Programming_mode (composite)

Schedule MODE ⏱ - In this mode, the device executes a preset week programming temperature time and temperature..

  • week (enum): Week format user for schedule allowed values: 5+2, 6+1, 7
  • workdays_schedule (text)
  • holidays_schedule (text)

Linkquality (numeric)

Link quality (signal strength). Value can be found in the published state on the linkquality property. It’s not possible to read (/get) or write (/set) this value. The minimal value is 0 and the maximum value is 255. The unit of this value is lqi.