TuYa TS0601_3_phase_clamp_meter
Model  TS0601_3_phase_clamp_meter 
Vendor  TuYa 
Description  3phase clamp power meter 
Exposes  ac_frequency, temperature, current, power, energy, energy_a, energy_b, energy_c, voltage_a, voltage_b, voltage_c, power_a, power_b, power_c, current_a, current_b, current_c, power_factor_a, power_factor_b, power_factor_c, linkquality 
Picture  
Whitelabel  MatSeePlus PC321ZTY 
Options
How to use device type specific configuration

temperature_precision
: Number of digits after decimal point for temperature, takes into effect on next report of device. The value must be a number with a minimum value of0
and with a with a maximum value of3

temperature_calibration
: Calibrates the temperature value (absolute offset), takes into effect on next report of device. The value must be a number. 
energy_precision
: Number of digits after decimal point for energy, takes into effect on next report of device. The value must be a number with a minimum value of0
and with a with a maximum value of3

energy_calibration
: Calibrates the energy value (percentual offset), takes into effect on next report of device. The value must be a number. 
current_precision
: Number of digits after decimal point for current, takes into effect on next report of device. The value must be a number with a minimum value of0
and with a with a maximum value of3

current_calibration
: Calibrates the current value (percentual offset), takes into effect on next report of device. The value must be a number. 
power_precision
: Number of digits after decimal point for power, takes into effect on next report of device. The value must be a number with a minimum value of0
and with a with a maximum value of3

power_calibration
: Calibrates the power value (percentual offset), takes into effect on next report of device. The value must be a number.
Exposes
Ac_frequency (numeric)
Measured electrical AC frequency.
Value can be found in the published state on the ac_frequency
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is Hz
.
Temperature (numeric)
Measured temperature value.
Value can be found in the published state on the temperature
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is °C
.
Current (numeric)
Instantaneous measured electrical current.
Value can be found in the published state on the current
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is A
.
Power (numeric)
Instantaneous measured power.
Value can be found in the published state on the power
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is W
.
Energy (numeric)
Sum of consumed energy.
Value can be found in the published state on the energy
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is kWh
.
Energy_a (numeric)
Sum of consumed energy (phase A).
Value can be found in the published state on the energy_a
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is kWh
.
Energy_b (numeric)
Sum of consumed energy (phase B).
Value can be found in the published state on the energy_b
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is kWh
.
Energy_c (numeric)
Sum of consumed energy (phase C).
Value can be found in the published state on the energy_c
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is kWh
.
Voltage_a (numeric)
Measured electrical potential value (phase A).
Value can be found in the published state on the voltage_a
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is V
.
Voltage_b (numeric)
Measured electrical potential value (phase B).
Value can be found in the published state on the voltage_b
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is V
.
Voltage_c (numeric)
Measured electrical potential value (phase C).
Value can be found in the published state on the voltage_c
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is V
.
Power_a (numeric)
Instantaneous measured power (phase A).
Value can be found in the published state on the power_a
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is W
.
Power_b (numeric)
Instantaneous measured power (phase B).
Value can be found in the published state on the power_b
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is W
.
Power_c (numeric)
Instantaneous measured power (phase C).
Value can be found in the published state on the power_c
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is W
.
Current_a (numeric)
Instantaneous measured electrical current (phase A).
Value can be found in the published state on the current_a
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is A
.
Current_b (numeric)
Instantaneous measured electrical current (phase B).
Value can be found in the published state on the current_b
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is A
.
Current_c (numeric)
Instantaneous measured electrical current (phase C).
Value can be found in the published state on the current_c
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is A
.
Power_factor_a (numeric)
Instantaneous measured power factor (phase A).
Value can be found in the published state on the power_factor_a
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is %
.
Power_factor_b (numeric)
Instantaneous measured power factor (phase B).
Value can be found in the published state on the power_factor_b
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is %
.
Power_factor_c (numeric)
Instantaneous measured power factor (phase C).
Value can be found in the published state on the power_factor_c
property.
It’s not possible to read (/get
) or write (/set
) this value.
The unit of this value is %
.
Linkquality (numeric)
Link quality (signal strength).
Value can be found in the published state on the linkquality
property.
It’s not possible to read (/get
) or write (/set
) this value.
The minimal value is 0
and the maximum value is 255
.
The unit of this value is lqi
.