OSRAM AC03641

   
Model AC03641
Vendor OSRAM
Description LIGHTIFY LED Classic A60 clear
Exposes light (state, brightness), effect, linkquality
Picture OSRAM AC03641

Notes

Pairing

To reset, start with the lighted powerd off. Power it on for 2 seconds and off for 5 seconds, five times in succession. When powering the lght on again, it flashes shortly once to confirm. After resetting the bulb will automatically connect.

Set default power on/off transition

Various Osram/Sylvania LED support setting a default transition when turning a light on and off.

TOPIC: zigbee2mqtt/FRIENDLY_NAME/set

{
    "set_transition": 1
}

INFO: Value is time in seconds (integer, float values are not supported)

Remember current light state

Various Osram/Sylvania LED support remembering their current state in case of power loss, or if a light is manually switched off then on. Lights will remember their respective attributes (i.e. brightness, color, saturation, etc.). NOTE: This must be executed every time you make changes to a light’s attributes for it to then ‘remember’ it.

TOPIC: zigbee2mqtt/FRIENDLY_NAME/set

{
    "remember_state": true
}

INFO: Value is true, false (boolean)

OTA updates

This device supports OTA updates, for more information see OTA updates.

Options

How to use device type specific configuration

  • transition: Controls the transition time (in seconds) of on/off, brightness, color temperature (if applicable) and color (if applicable) changes. Defaults to 0 (no transition). The value must be a number with a minimum value of 0

  • state_action: State actions will also be published as ‘action’ when true (default false). The value must be true or false

Exposes

Light

This light supports the following features: state, brightness.

  • state: To control the state publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"state": "ON"}, {"state": "OFF"} or {"state": "TOGGLE"}. To read the state send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"state": ""}.
  • brightness: To control the brightness publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"brightness": VALUE} where VALUE is a number between 0 and 254. To read the brightness send a message to zigbee2mqtt/FRIENDLY_NAME/get with payload {"brightness": ""}.

Transition

For all of the above mentioned features it is possible to do a transition of the value over time. To do this add an additional property transition to the payload which is the transition time in seconds. Examples: {"brightness":156,"transition":3}, {"color_temp":241,"transition":1}.

Moving/stepping

Instead of setting a value (e.g. brightness) directly it is also possible to:

  • move: this will automatically move the value over time, to stop send value stop or 0.
  • step: this will increment/decrement the current value by the given one.

The direction of move and step can be either up or down, provide a negative value to move/step down, a positive value to move/step up. To do this send a payload like below to zigbee2mqtt/FRIENDLY_NAME/set

NOTE: brightness move/step will stop at the minimum brightness and won’t turn on the light when it’s off. In this case use brightness_move_onoff/brightness_step_onoff

{
  "brightness_move": -40, // Starts moving brightness down at 40 units per second
  "brightness_move": 0, // Stop moving brightness
  "brightness_step": 40 // Increases brightness by 40
}

Effect (enum)

Triggers an effect on the light (e.g. make light blink for a few seconds). Value will not be published in the state. It’s not possible to read (/get) this value. To write (/set) a value publish a message to topic zigbee2mqtt/FRIENDLY_NAME/set with payload {"effect": NEW_VALUE}. The possible values are: blink, breathe, okay, channel_change, finish_effect, stop_effect.

Linkquality (numeric)

Link quality (signal strength). Value can be found in the published state on the linkquality property. It’s not possible to read (/get) or write (/set) this value. The minimal value is 0 and the maximum value is 255. The unit of this value is lqi.